СБРОС ПАМПЕРСОВ CANON

2019-11-25 00:45:47 0 114

Canon "S" серия

1. Выключить принтер.
2. Нажать и удерживая кнопку RESUME нажать и удерживать POWER.
3. Отпустить RESUME, затем нажать и отпустить RESUME 2 раза.
POWER все еще удерживать. Каретка сдвинется ипринтер войдет в сервисный режим.
4. Нажать RESUME 4 раза - это сброс памперса - clear waste ink counter function. Количество нажатий соответствует разным функциям:
1 раз - Service/Factory test printout, including ink sensor check.
2 раза - EEPROM - Info printout.
3 раза - EEPROM - Initialization.
4 раза - Reset the Waste ink counter.
5 раз - Printer model setting.
6 и более раз - другие не нужные и опасные для юзера функции.
После выбора опции путем нажатий нужного кол раз - нажать POWER для записи изменений
и возврата в предыдущее меню. Нажать еще раз POWER для перезапуска принтера.
УсЁ!

===================================

S820D, S9000

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Model setting (1 time)
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 и выше...

1. Выключить принтер.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

===================================

Canon S900, S820, S750, S520

1. Выключить принтер.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu.
6. Pressing the POWER button again turns off the printer for a restart.

===================================

Canon S9000

1. Выключить принтер.
2. Удерживая кнопку Resume нажмите кнопку Power.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
Green lights will flash and then stop blinking.
5. When green lights are solid, press the Resume button 4 times.
6. Выключите принтер. Если с первого раза принтер не выключился - нажмите кнопку питания еще раз.
Блокировка сброшена. Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

Canon i320, i255

Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2. Open General Tools software and select (USB PORT)
3. Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

===================================

i450, i455

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.

Zero times - Green - Power off the printer
2 times - Green - EEPROM information print
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i470D, i475D

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM reset (all data cleared except USB serial number)
4 times - Green - Waste ink counter setting
6 times + - Green - Print head deep cleaning
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i550, i560

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power and Resume button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Head refreshing
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

Canon i850, i950, S600

Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

===================================

i850, i860

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power and Resume button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Head refreshing
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i900D

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Print head deep cleaning
7 times - Orange - Media sensor correction
8 times - Green - Button and LCD viewer test
9 times - Orange - Return to menu selection
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i950
1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
8 times - Green - Roller cleaning
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i960

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Print head deep cleaning
7 times - Orange - Media sensor correction
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

i80

1) Turn off the printer. While pressing the Resume/Cancel button, press the Power button.
2) While holding the Power button, release the Resume/Cancel button.
3) While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons.
4) When the LED stops blinking and lights in green, press the Resume/Cancel button the specified number of time(s) according to the function listed in the table below.

0 times - Green - Power off
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter resetting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - USB serial number reset
7 times - Orange - USB serial number setting to default shipment value
10 times - Green - Return to the menu selection
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

PIXMA iP90

Service mode operation procedures.
1) Turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button.
3) While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons.
4) When the LED stops blinking and lights in green, press the Resume/Cancel button the specified number of time(s) according to the function listed in the table below.

0 times - Green - Power off
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter resetting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
10 times - Green - Return to the menu selection
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

Canon PIXMA iP1000

Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

===================================

Canon PIXMA iP1500

Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

===================================

Canon PIXMA iP2000

1. Выключить принтер
2. Нажать и удерживаеть кнопку RESUME
3. Нажать кнопку POWER
4. Не отпуская кнопку Power отпустить и снова два раза нажать кнопку RESUME и отпустить кнопку POWER
5. После того как индикатор поморгает - попали в сервисный режим
6. Нажать кнопку RESUME 4 раза для сброса памперса или 3 раза для сброс EEPROM. При каждом нажатии кнопки RESUME индикатор меняет цвет: зеленый-оранжевый
7. Нажать кнопку питания Power.
8. Еще раз POWER - выход из сервисного режима.
Дополнительная информация находится на сайте www.servicemanuals.ru.

-------- Добавление от нашего читателя ----------------
Для iP2000 возможны три варианта сброса счетчика :
После входа в функцию сброса счетчика (выбор - 4 нажатия кнопки RESUME и подтверждения выбора кнопкой POWER ) кнопкой RESUME ввести –
- 0 нажатий – сброс главного счетчика в 0%, или
- 1 нажатие – сброс дополнительного (platen) счетчика в 0%, или
- 2 нажатия – установка главного счетчика на 50%
-нажать POWER для выполнения сброса.
-------------------------------------------------------------

===================================

Canon PIXMA iP3000, iP4000, iP5000

1. Выключите принтер.
2. Удерживая кнопку RESUME/CANCEL нажмите кнопку питания POWER - загорится зеленый индикатор.
3. Удерживая кнопку POWER отпустите кнопку RESUME.
4. Нажмите кнопку RESUME/CANCEL два раза все еще удерживая кнопку POWER а затем отпустите все кнопки.
5. Когда индикатор засветится зеленым - нажмит 4 раза кнопку RESUME/CANCEL.

1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Network setting information printing
10 times - Green - Initialization of network setting information

6. Выключите принтер. Блокировка сброшена. Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

PIXMA iP4200, iP5200

1. Выключите принтер.
2. Удерживая кнопку Resume нажмите кнопку POWER.
3. Удерживая кнопку POWER отпустите кнопку RESUME.
4. Затем нажмите два раза снова кнопку RESUME.
5. Отпустите все кнопки.
6. Индикатор моргнет зеленым цветом и останется зеленым.
7. Нажмите 4 раза кнопку RESUME для сброса памперса или иное количество раз, если нужно произвести другую операцию. Смотрите по таблице:

1 раз - Orange - Service test print
2 раз - Green - EEPROM information print
3 раз - Orange - EEPROM initialization
4 раз - Green - Waste ink counter setting
5 раз - Orange - Destination setting (Press Power > Press Resume 3x)
6 раз - Green - Print head deep cleaning
11-13 раз - Orange, Green, Orange - Return to menu selection
14 раз - Green - Left margin correction

8. Выключите принтер кнопкой POWER.
Информация взята из сервисного мануала.
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

PIXMA iP6000D

1) With the printer powered off, hold down the Resume button and press the Power button.
2) While holding down the Power button, release the Resume button and press the Resume button twice in succession. Now release the Power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times - Green - Power off the printer
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Print head deep cleaning
10 times - Green - Button and LCD viewer test
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

PIXMA iP8500

1) With the printer powered off, hold down the Resume button and press the Power button. Continue holding down the Power button, then release the Resume button. Press the Resume button twice in succession. Now release the Power and Resume button. The indicator will blink in green and remain lit in green.
2) Select one of the following service mode functions by pressing the Resume button the specified number of times.

Zero times Green Print head not installed, carriage returns and locks in home position
1 time - Orange - Service test print
2 times - Green - EEPROM information print
3 times - Orange - EEPROM initialization
4 times - Green - Waste ink counter setting
5 times - Orange - Destination setting (Press Power > Press Resume 3x)
6 times - Green - Print head deep cleaning
10 times - Green - Return to menu selection
Дополнительная информация находится на сайте www.servicemanuals.ru.

===================================

Canon S450 Printer

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7: Press Power to set data
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC 1000 Serie

1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-2000 BJC-2100 Serie

1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-5000

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-5100

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500

1. Выключить принтер.
2. Удерживая кнопку RESUME нажать и удерживать POWER - прозвучит 1 сигнал.
3. Удерживая POWER отпустить RESUME.
4. Нажать RESUME 2 раза.
5. When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6. Нажать Power чтобы данные записались и сохранились.
Дополнительная информация находится на сайте www.servicemanuals.ru

===================================

Canon BJC-600 BJC-600e BJC-610 BJC-620

1. Отключить кабель питания.
2. Нажать и удерживать POWER, FF и Print Mode кнопки.
3. Подключить кабель питания.
4. Отпустить после сигналов.
Дополнительная информация находится на сайте www.servicemanuals.ru

================================

Комментарии: